![colt mustang date of manufacture colt mustang date of manufacture](https://s3.amazonaws.com/mgm-content/sites/armslist/uploads/posts/2020/06/05/11908855_01_colt_mustang_plus_ii_640.jpg)
- #Colt mustang date of manufacture serial numbers#
- #Colt mustang date of manufacture code#
- #Colt mustang date of manufacture series#
#Colt mustang date of manufacture code#
MH 0165xx slab side lower, big pivot pin, sear block pinned in on both sides (with two on the left?), CM forge code A2 upper? roll marked COLT'S MFG? MH 013495 A2 lower with mag fense, big hole pivot pin, sear block pinned on both side, CM upper, made in 1991 MH 010063 slab lower with no sear block, roll marked COLT'S MFG MH 008XX slab lower with no sear block, 1990 manufacture MH 007657 slab lower with no sear block, CM upper, roll marked COLT'S MFG, 1990 manufacture MH 006600 and up have large trigger/hammer pins MH 001001 A2 lower, big hole pivot pin, no sear block 22 conversion kit, built in 1990Ģ497XX CM upper forge code, big pin slab lower with no sear block, modern small forward assist, roll marked SPORTER MATCH HBAR, SPORTER bolt carrier, bolt marked MPC with a space between the M and the P, blue extractor buffer, barrel stamped C MP 5.56 NATO 1/7 HBAR, peel washer, A2 furniture, no bayo lug, small hammer/trigger pin holes, roll marked COLT'S MFG, blue label 6601 box, purchased in June of 1990 In general these have the following features:ĬM or CMB upper forge code, modern small forward assist, roll marked SPORTER MATCH HBAR, SPORTER bolt carrier, bolt marked MPC with a space between the M and the P, blue extractor buffer, barrel stamped C MP 5.56 NATO 1/7 HBAR, peel washer, A2 furniture, no bayo lugĢ47401 CM upper forge code, big hole slab side lower, no sear block, no auto sear cut in upper, small pin hammer/trigger pins, modern small forward assist, SP1 bolt carrier, bolt marked MPC with a space between the M and the P, blue extractor buffer, AR-15 A2 HBAR SPORTER, lower roll marked COLT’S FIREARM DIVISION, barrel stamped C MP 5.56 NATO 1/7 HBAR, peel washer, A2 furniture, this is a R6600K, no bayonet lug, with a.
![colt mustang date of manufacture colt mustang date of manufacture](https://s3.amazonaws.com/mgm-content/sites/armslist/uploads/posts/2020/04/21/11645045_03_colt_mustang_plus_ii_stainless_640.jpg)
The Delta HBAR, R6600DH was introduced in 1987.Ģ15677 appeared in the May 1986 issue of American RiflemanĢ49256 this is a Delta H-BAR, as in R6600DH, white label box Not going to list features of each example, unless they are different then indicated above. Features are as such:ĬM upper forge code, big hole slab side lower, no sear block, no auto sear cut in upper, small pin hammer/trigger pins, modern small forward assist, SP1 bolt carrier, bolt marked MPC with a space between the M and the P, blue extractor buffer, AR-15 A2 HBAR SPORTER, lower roll marked COLT’S FIREARM DIVISION, barrel stamped C MP 5.56 NATO 1/7 HBAR, peel washer, A2 furniture, bayo lug
#Colt mustang date of manufacture serial numbers#
Serial numbers picks up were the SP1 left off, produced 1985-1990. So yours should have these bigger trigger/hammer pins unless yours was an older COLT FIREARM DIVISION lower? Trigger pins were switched to the bigger size starting with MH 006600. You fits into the later MH029XXX features rather then the earlier type. Get the Mustang and a 10 rnd mag or two and you will be happy.Here is an updated HBAR data base. I never could see the reasoning in that because any encounter you are likely to have will, probably, not involve the need to part someone's hair at 50 yds. I'm also sure that someone will say that a small gun has a short sight radius that hinders aiming. 380 is pure SA and has a nice, crisp trigger that does not cause muscle shake. The S&W is better but still a bit of a problem. They are all DAO and they all have a long, grinding trigger pull that really messes with my aim. I, also, currently own an LCP, LC9 and S&W M&P 9C. 380 can do a lot of damage and you are more likely to be carrying a smaller, lighter gun that you can hit something with.
![colt mustang date of manufacture colt mustang date of manufacture](https://gvx.blob.core.windows.net/item-images/value-p-1108632.jpg)
I notice we had a caliber snob check in on this thread but when you have to deal with reality a. I have two of those but I will say that I had to send one back for replacement because of feed problems. The standard magazine holds 7 rounds but U.S.A. I believe the Mustang model is identical except for a slightly shorter barrel and slide and the Mustang is currently back in production. I looks like a 1911, fits my hand to perfection and has had flawless performance. 380 last year and it is absolutely great.
![colt mustang date of manufacture colt mustang date of manufacture](https://media.mwstatic.com/product-images/src/primary/459/459783.jpg)
#Colt mustang date of manufacture series#
I bought a used Mark IV series 80 government.